Gnee  Stål  (Tianjin)  Co.,  Ltd.

Mekaniske egenskaber ved titanium

Jun 13, 2025

Mekaniske egenskaber ved titanium:
① Ren titanium trækstyrke på 265 ~ 353MPa, generelle titaniumlegeringer for 686 ~ 1176MPa, det aktuelle maksimum på 1764MPa . titan -legering
② The compressive strength of titanium and titanium alloys is not less than their tensile strength. The compressive yield strength and tensile yield strength of industrial pure titanium are roughly equal, while the compressive strength of Ti-6AI-4V and Ti-5AI-2.5Sn is slightly higher end trækstyrken .
Ti {-6 ai -4 v og ti {{2} {-2.5 sn er lidt højere end trækstyrken {{4 {{{0-6 ai {{-4
④ Under normale atmosfæriske forhold er udholdenhedsgrænsen for forarbejdet og annealet titanium og titaniumlegeringer 0 . 5 til 0 . 65 trækstyrke. Udholdenhedsgrænsen for annealet ti -6 ai -4 V er 0,2 gange trækstyrken, når træthedstestene udføres 10 millioner gange i den hakket tilstand (kt =3.9).
⑤ The hardness of the highest purity grade of processed industrially pure titanium is usually less than 120 HB (Brinell), and the hardness of other industrially pure processed titanium is 200-295 HB. The hardness of pure titanium castings is 200-220 HB. The hardness of titanium alloys in the annealed condition is {{5. (Kt =3.9) . ti -6 ai -4 V i den støbte tilstand har en hårdhed på 320 HB, og ti -6 al -4 V støbning med lav interstitial nøjehaver har en hårdhed på 310 HB.
⑥ Trækmodulet for elasticitet af industrielt rent titan er 105 til 109 GPa De fleste titanlegeringer har en trækmodul for elasticitet i den annealede tilstand af 110 til 120 GPa . aldershærdet titanlegeringer har en lidt højere modul af elasticitet i tensile tilstand end i den anvealede tilstand, og den afmængermodul af elasticiteten af ​​elasticitet Elasticitet er lig med eller større end trækmodulets elasticitetsmodul . Den specifikke modul for elasticitet af titanlegeringer er lig med aluminiumslegeringer, kun anden til beryllium, molybden og nogle høje temperaturlegeringer .
(8 Depending on the type and state of the titanium alloy, the value of the Charpy notched impact strength of densified industrially pure titanium is 15-54J/m2, and about 4-10J/m2 in the casting state. The impact strength of titanium alloys in the annealed state is 13 to 25.8 J/㎡, and slightly Lavere i den ældre tilstand . støbt tilstand af ti -5 ai -2.5 sn charcot v-notch påvirkningsstyrke på 10J/㎡, ti -6 ai -4 v for {20-23 j/㎡ .}} oxygen-indholdet af titan Legeringer, jo højere værdien.
) Ikke-notched-trækstyrkeforhold er større end 1.
⑨ Titanium alloys at high temperatures can also maintain a certain performance. General industrial titanium alloy at 540℃temperature can maintain its performance, but only for short-term applications, long enough for the temperature range of 450 ~ 480℃. Titanium alloys have been developed for use at temperatures of 600℃. Titanium alloy as a missile Materiale kan bruges i lang tid ved en temperatur på 540 grad, kan også bruges i kort tid ved en temperatur på 760 grader .

titanium pipes for exhaustthin wall titanium tubingsmall diameter titanium tubing

⑩Titanium- og titaniumlegeringer kan stadig opretholde deres originale mekaniske egenskaber ved lave og ultra-lave temperaturer . Når temperaturen falder, forværres styrken af ​​titanium og titaniumlegeringer, mens duktiliteten graduelt forværres {. mange anvingede titaniumlegeringer har tilstrækkelig ductilitet og frafract sejhed ved {{3 3℃. Ti-5AI-2.5Sn, which contains a very low amount of interstitial elements, can be used at temperatures up to -252.7℃. It has a very low notched tensile strength compared to non-notched titanium alloys. Its ratio of Indhakket trækstyrke til ikke-nukket trækstyrke er 0 . 95 til 1,15 ved -25.7 grad.
Liquid oxygen, liquid hydrogen and liquid fluorine are important propellants in missiles and space devices. The cryogenic properties of the materials used to make cryogenic gas containers and cryogenic structural components are very important. When the microstructure is isometric and the content of interstitial elements (oxygen, helium, hydrogen, osv. .) er meget lav, duktiliteten af ​​titan -legeringer forbliver over 5 procent . De fleste titanlegeringer har dårlig duktilitet ved en temperatur på -252.7 grad, mens ti -6 ai -4 V har en langvarig af 12 pr. Cent {{.

 

Vi kan levere produkter af høj kvalitet, god service og konkurrencedygtige pris . Vi har været forpligtet til at fremstille titaniumprodukter af høj kvalitet, såsom titanrør, titantråd, titanplader, titaniumstrimler, titanstænger og andre titanprodukter .}

Pøbel: +8615824687445

E-mail:sales@gneesteel.com

Skype: Mmkelly1314

WhatsApp/WeChat: +86 15824687445

titanium welded tube

goTop